Air Gap For Water Softener Waste Pipes

Dvdfab 8 Qt Free Download. Air gaps are required by many plumbing codes (UPC - Uniform Plumbing Code is one) for dishwashers and for water softeners. We offer dishwasher air gaps in a large selection of finishes to help you match your kitchen sink and/or faucet. We also offer an. Air gaps have no moving parts and use the (free) atmosphere to protect from the reversal of contaminants. We believe that no matter what the local code dictates, every dishwasher discharge, in order to protect your family's health, must go into an airgap before discharging into a food/garbage disposer or drain. Frequently Asked Questions Q. 'Why do I need an air gap?'

Air gaps are required by most plumbing codes for dishwashers and for water softeners. They are needed to prevent any possible cross-connection between your potable water system and your sewage system. Without an air gap, there is always a chance (however slim) of siphoning contaminants from your sewage system into your drinking water system. 'Will your softener air gap fit the discharge line from my softener?' It is designed for the that we sell as well as most large softeners. It is for 1/2' i.d.

Hose, which is the same size as the discharge on our. The 90-degree connection can be installed in any direction and you simply glue it into place once you are happy with the setup. 'It says that the water softener air gap fits a 2' standpipe.

This kit has everything you need to attach a 3/8' Softener waste to an under the sink waste pipe. Includes the plumbing out kit to clamp around the waste pipe, a trap.

Please explain a little better.' The air gap is designed to fit inside of a 2' standard (schedule 40) PVC pipe or ABS pipe. It's best to glue it into place with a multipurpose glue for PVC/ABS plastic, but many people have simply installed into their plastic pipe and not glued it.

It also will fit inside most steel or cast iron standpipes (a standpipe is the pipe that is for clothes washers). If you have a 1 1/2' standpipe this air gap can work but it is more trouble to install and you'll need a 2' piece of ABS or PVC schedule 40 pipe, and a 2' x 1 1/2' ABS or PVC coupling depending on your type of pipe. Adobe Photoshop Cs3 Free Download Crack Keygen Patches on this page.

The easiest way to install this softener air gap onto a 1 1/2' standpipe is to order our that has a stainless steel clamp to attach onto a 1 1/2' pipe. 'My airgap on my sink keeps spitting water every time that I run our dishwasher. What is wrong?'

Quality made air gaps are pretty basic products that rarely go 'bad'. If you purchased your airgap from us you can rest assured that it is a quality airgap. IF your air gap didn't spit in the past then try running your garbage disposer for a few minutes. Basically the way your dishwasher airgap works is that water is pumped through the smaller side of the airgap (5/8') into the airgap and then gravity takes it to your sink (or disposer) with larger hose (7/8'). The larger size has an area of about twice as large and with gravity there normally isn't any problem. If the 7/8' hose is sagging or there is grease build up or a partial stoppage or blockage in your sink/disposer the airgap can 'spit.'

After inspecting under the sink to make sure the 7/8' hose isn't kinked or going uphill at all (it has to go smoothly downhill all the way) then disconnect the 7/8' hose at the sink/disposer and point it into a large bucket. Then run the dishwasher and see if the airgap still spits. If it does then you know you need a new airgap and if it doesn't then you know the 'problem' is after the hose. 'What are the sizes on the inlet and outlet of the dishwasher air gaps?'

Standard 5/8' i.d. (requires 5/8' inside diameter hose) for the inlet and 7/8' i.d.

Hose for the outlet.